BS EN 60086-1:2011
$198.66
Primary batteries – General
| Published By | Publication Date | Number of Pages |
| BSI | 2011 | 54 |
This part of IEC 60086 is intended to standardize primary batteries with respect to dimensions, nomenclature, terminal configurations, markings, test methods, typical performance, safety and environmental aspects.
As a primary battery classification tool, electrochemical systems are also standardized with respect to system letter, electrodes, electrolyte, nominal and maximum open circuit voltage.
NOTE The requirements justifying the inclusion or the ongoing retention of batteries in the IEC 60086 series are given in Annex A.
The object of IEC 60086-1 is to benefit primary battery users, device designers and battery manufacturers by ensuring that batteries from different manufacturers are interchangeable according to standard form, fit and function. Furthermore, to ensure compliance with the above, this part specifies standard test methods for testing primary cells and batteries.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | English CONTENTS |
| 9 | INTRODUCTION |
| 10 | 1 Scope 2 Normative references 3 Terms and definitions |
| 13 | 4 Requirements 4.1 General Figures Figure 1 – Small cell or battery gauge (inner dimensions) |
| 15 | Figure 2 – Stud Tables Table 1 – Spacing of contacts Table 2 – Snap fastener connectors |
| 16 | Table 3 – Standardized electrochemical systems |
| 17 | Table 4 – Marking requirements |
| 18 | 4.2 Performance |
| 19 | 5 Performance – Testing 5.1 General 5.2 Discharge testing |
| 20 | 5.3 Conformance check to a specified minimum average duration |
| 21 | 5.4 Calculation method of the specified value of minimum average duration 5.5 OCV testing 5.6 Battery dimensions 5.7 Leakage and deformation 6 Performance – Test conditions 6.1 Pre-discharge conditioning Table 5 – Conditions for storage before and during discharge testing |
| 22 | 6.2 Commencement of discharge tests after storage 6.3 Discharge test conditions 6.4 Load resistance 6.5 Time periods Table 6 – Resistive loads for new tests Table 7 – Time periods for new tests |
| 23 | 6.6 Test condition tolerances 6.7 Activation of ‘P’-system batteries 6.8 Measuring equipment 7 Sampling and quality assurance 7.1 General 7.2 Sampling Table 8 – Test condition tolerances |
| 24 | 7.3 Product quality indices |
| 25 | 8 Battery packaging |
| 26 | Annex A (normative) Guidelines for the standardization of batteries Table A.1 – Items necessary to standardize |
| 27 | Annex B (normative) Equipment design |
| 29 | Annex C (normative) Designation system (nomenclature) |
| 30 | Table C.1 – Physical designation and dimensions of round cells and batteries |
| 31 | Table C.2 – Physical designation and nominal overall dimensions of flat cells Table C.3 – Physical designation and dimensions of square cells and batteries |
| 34 | Figure C.2 – Diameter code for non-recommended diameters Table C.4 – Diameter code for recommended diameters |
| 37 | Figure C.5 – Designation system for non-round batteries, dimensions < 100 mm |
| 40 | Table C.5 – Physical designation and dimensions of round cells and batteries based on Clause C.2 |
| 41 | Table C.6 – Physical designation and dimensions of non-round batteries based on Clause C.2 |
| 42 | Annex D (normative) Calculation method for the specified value of minimum average duration |
| 43 | Annex E (normative) Code of practice for packaging, shipment, storage, use and disposal of primary batteries |
| 46 | Annex F (informative) Standard discharge voltage Us – Definition and method of determination |
| 47 | Figure F.1 – Normaliz3ed C/R-plot (schematic) |
| 48 | Figure F.2 – Standard discharge voltage (schematic) |
| 49 | Table F.1 – Standard discharge voltage by system |
| 50 | Annex G (informative) Preparation of standard methods of measuring performance (SMMP) of consumer goods |
| 51 | Bibliography |
