BS EN 60810:1995:2002 Edition
$167.15
Specification for lamps for road vehicles. Performance requirements
| Published By | Publication Date | Number of Pages |
| BSI | 2002 | 34 |
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | BRITISH STANDARD |
| 2 | Committees responsible for this British Standard |
| 3 | Short contents |
| 6 | Foreword Foreword to amendment A1 Foreword to amendment A2 |
| 7 | Contents |
| 9 | Section 1. General 1.1 Scope 1.2 Normative references |
| 10 | 1.3 Definitions 1.3.1 life 1.3.2 characteristic life 1.3.3 life B3 1.3.4 lumen maintenance 1.3.5 initial luminous flux 1.3.6 rated value 1.3.7 pinch temperature limit 1.3.8 solder temperature limit 1.3.9 maximum filament lamp outline 1.3.10 heavy duty filament lamp |
| 11 | 2.1 Basic function and interchangeability 2.2 Torsion strength 2.3 Characteristic life T 2.4 Life B3 Table 1 2.5 Lumen maintenance 2.6 Resistance to vibration and shock |
| 12 | Table 2 2.7 Glass bulb strength |
| 13 | Section 3. Guidance for equipment design 3.1 Pinch temperature limit 3.2 Solder temperature limit 3.3 Maximum filament lamp outline 3.4 Maximum surge voltage 3.5 Recommended instructions for use of halogen filament lamps 3.6 Recommended instructions for use of discharge lamps |
| 15 | Section 4. Filament lamp data 4.1 Rated life and lumen-maintenance values for road vehicle filament lamps tested under conditions a… Table 3 |
| 16 | Table 4 |
| 17 | 5.1 Basic function and interchangeability 5.2 Mechanical strength 5.2.1 Bulb to cap connection 5.2.2 Cable to cap connection (if any) 5.3 Characteristic life T 5.4 Life B3 5.5 Lumen maintenance 5.6 Resistance to vibration and shock |
| 18 | Annex A (normative) Life test conditions for filament lamps A.1 Ageing A.2 Test voltage A.3 Operating position A.4 Switching cycle A.4.1 Single filament lamps A.4.2 Dual filament lamps for headlamps A.4.3 Dual filament lamps for light signalling equipment |
| 19 | A.5 Lumen maintenance Annex B (normative) Vibration tests B.1 General B.2 Test conditions |
| 20 | B.2.1 Mounting B.2.2 Measuring points B.2.3 Control point B.2.4 Conditioning B.2.5 Axis of vibration B.2.6 WBR test — Basic motion B.3 Test requirements |
| 21 | B.3.1 Narrow-band random vibration tests Table B.1 Table B.2 |
| 22 | B.3.2 Wide-band random vibration tests Table B.3 Figure B.1 |
| 23 | Annex C (normative) Glass bulb strength test C.1 General C.2 Test equipment and procedure C.2.1 The principle of the test equipment Figure C.1 C.2.3 Requirements for plates Table C.1 |
| 24 | C.3 Requirements C.4 Evaluation C.4.1 Assessment based on attributes Table C.2 |
| 25 | C.4.2 Assessment based on variables Table C.3 |
| 26 | Figure 1 |
| 27 | Figure 2 |
| 28 | Figure 3 |
| 29 | Figure 4 |
| 30 | Figure 5 |
| 31 | Annex D (normative) Life and lumen maintenance test conditions for discharge lamps D.1 Ageing D.2 Test circuit and test voltage D.3 Burning position and operating conditions D.4 Switching cycle D.5 Lumen maintenance |
| 32 | Annex E (normative) Bulb deflection test E.1 General E.2 Test set-up and procedure E.2.1 Sketch of the test set-up E.2.2 Test procedure E.3 Requirement |
| 33 | Annex ZA (normative) Other international publications quoted in this standard with the references of the r… |
