BS EN IEC 60317-0-6:2020
$142.49
Specifications for particular types of winding wires – General requirements. Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 24 |
IEC 60317-0-6:2020 is available as IEC 60317-0-6:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60317-0-6:2020 specifies the general requirements of glass-fibre wound resin or varnish impregnated, bare or enamelled, round copper winding wires. The range of nominal conductor diameters is given in the relevant specification sheet. This second edition cancels and replaces the first edition published in 2001 and Amendment 1:2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: – revision to 3.3, Appearance; – revision to Table 1, maximum overall diameter of grade 1 wire over single-glass fibre covering for nominal conductor diameters 1,600 mm – 5,000 mm; – revision to Table 2, maximum overall diameter of grade 1 wire over double-glass fibre covering for nominal conductor diameters 1,600 mm – 5,000 mm; clarification in Table 3 measurement of elongation as “minimum elongation %”.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 5 | Annex ZA(normative)Normative references to international publicationswith their corresponding European publications |
| 7 | English CONTENTS |
| 9 | FOREWORD |
| 11 | INTRODUCTION |
| 12 | 1 Scope 2 Normative references 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions |
| 13 | 3.2 General notes 3.2.1 Methods of test |
| 14 | 3.2.2 Winding wire 3.3 Appearance 4 Dimensions 4.1 Conductor diameter |
| 15 | Tables Table 1 – Diameters for single glass-fibre covered grade 1or grade 2 enamelled round wires Table 2 – Diameters for double glass-fibre covered, bare, grade 1or grade 2 enamelled round wires |
| 16 | 4.2 Out of roundness of the conductor 4.3 Minimum increase in diameter due to the covering 4.4 Maximum overall diameter |
| 17 | 5 Electrical resistance 6 Elongation 7 Springiness 7.1 Nominal conductor diameters up to and including 1,600 mm 7.2 Nominal conductor diameters over 1,600 mm 8 Flexibility and adherence 9 Heat shock 10 Cut-through 11 Resistance to abrasion Table 3 – Elongation |
| 18 | 12 Resistance to solvents 13 Breakdown voltage 13.1 Glass-fibre covered bare round copper wires 13.2 Glass-fibre covered enamelled round copper wires 14 Continuity of insulation 15 Temperature index Table 4 – Breakdown voltage for glass-fibre covered bare round copper wires Table 5 – Breakdown voltage of glass fibre-covered enamelled round copper wires |
| 19 | 16 Resistance to refrigerants 17 Solderability 18 Heat or solvent bonding 19 Dielectric dissipation factor 20 Resistance to hydrolysis and to transformer oil 21 Loss of mass 23 Pin hole test 30 Packaging |
| 20 | Annex A (informative) Diameters for intermediate nominal conductor diameters (R40) Table A.1 – Diameters for single glass-fibre covered grade 1 or grade 2 enamelled round wires (R40) |
| 21 | Table A.2 – Diameters for double glass-fibre covered, bare, grade 1 or grade 2 enamelled round wires (R40) |
| 22 | Annex B (informative) Resistance Table B.1 – Electrical resistances |
| 23 | Bibliography |
