🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN IEC 61169-71:2022

BS EN IEC 61169-71:2022

$167.15

Radio-frequency connectors – Sectional specification for RF coaxial connectors with inner diameter of outer conductor 5 mm. Characteristic impedance 50 Ohms. type NEX10®

Published By Publication Date Number of Pages
BSI 2022 38
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connector, typically for use in 50 Ω radio communication systems, type NEX10®. This document describes mating face dimensions for general purpose connectors – grade 2, dimensional details of standard test connectors-grade 1, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to type NEX10® RF coaxial connectors. This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H. The type NEX10® RF coaxial connectors are used with all kinds of RF cables and microstrip circuits in radio frequency transmission systems with operating frequencies up to 20 GHz. NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for reference purpose only.

PDF Catalog

PDF Pages PDF Title
2 undefined
5 Annex ZA (normative)Normative references to international publicationswith their corresponding European publications
6 Blank Page
7 English
CONTENTS
9 FOREWORD
11 INTRODUCTION
12 1 Scope
2 Normative references
3 Terms and definitions
13 4 Mating face and gauge information
4.1 General purpose connector: Grade 2
4.1.1 Screw type connector with pin centre contact
Figures
Figure 1 – Screw type connector with pin centre contact
14 4.1.2 Quick lock type connector with pin centre contact
Tables
Table 1 – Dimensions of screw type connector with pin centre contact
15 Figure 2 – Quick lock type connector with pin centre contact W
Table 2 – Dimensions of quick lock type connector with pin centre contact
16 4.1.3 Connector with socket centre contact
17 Figure 3 – Connector with socket centre contact
18 4.2 Gauges
4.2.1 Gauge pin for socket centre contact
Table 3 – Dimensions of connector with socket centre contact
19 4.2.2 Gauge rings for plug outer contact
Figure 4 – Gauge pin for socket centre contact
Table 4 – Dimensions of gauge pin for socket centre contact
20 4.3 Standard test connectors: Grade 1
4.3.1 Standard test connector with pin centre contact
Figure 5 – Gauge rings for plug outer contact
Table 5 – Dimensions of gauge rings for plug outer contact
21 Figure 6 – Standard test connector with pin centre contact interface
22 4.3.2 Standard test connector with socket centre contact
Table 6 – Interface dimensions of standard test connector with pin centre contact
23 Figure 7 – Standard test connector with socket centre contact interface
24 Table 7 – Interface dimensions of standard test connector with socket centre contact
25 5 Quality assessment procedures
5.1 General
5.2 Ratings and characteristics
Table 8 – Ratings and characteristics
27 5.3 Test schedule and inspection requirements
5.3.1 Acceptance tests
28 5.3.2 Periodic tests
Table 9 – Acceptance tests
29 Table 10 – Periodic tests
30 5.4 Procedures for the quality conformance
5.4.1 Quality conformance inspection
5.4.2 Qualification approval and its maintenance
31 6 Instructions for preparation of detail specifications
6.1 General
6.2 Identification of the component
6.3 Performances
6.4 Marking, ordering information and related matters
6.5 Selection of tests, test conditions and severities
32 6.6 Blank detail specification pro-forma for RF coaxial connector with inner diameter of outer conductor 5 mm with screw coupling-characteristic impedance 50 ohms (type NEX10®)
37 Bibliography

Related products

BS EN IEC 61169-71:2022
$167.15