🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-D6216:2007 Edition

ASTM-D6216:2007 Edition

$58.50

D6216-07 Standard Practice for Opacity Monitor Manufacturers to Certify Conformance with Design and Performance Specifications

Published By Publication Date Number of Pages
ASTM 2007 37
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

1.1 This practice covers the procedure for certifying continuous opacity monitors. In the main part of this practice, it includes design and performance specifications, test procedures, and quality assurance requirements to ensure that continuous opacity monitors meet minimum design and calibration requirements, necessary in part, for accurate opacity monitoring measurements in regulatory environmental opacity monitoring applications subject to 10 % or higher opacity standards. In Annex A1, additional or alternative specifications are provided for certifying opacity monitors intended for use in applications where the opacity standard is less than 10 %, or where the user expects the opacity to be less than 10 % and elects to use the more restrictive criteria in Annex A1. In both cases, the error budgets for the opacity measurements are given in Appendix X1.

1.2 This practice applies specifically to the original manufacturer, or to those involved in the repair, remanufacture, or resale of opacity monitors.

1.3 Test procedures that specifically apply to the various equipment configurations of component equipment that comprise either a transmissometer, an opacity monitor, or complete opacity monitoring system are detailed in this practice.

1.4 The specifications and test procedures contained in the main part of this practice have been adopted by reference by the United States Environmental Protection Agency (USEPA). For each opacity monitor or monitoring system that the manufacturer demonstrates conformance to this practice, the manufacturer may issue a certificate that states that opacity monitor or monitoring system conforms with all of the applicable design and performance requirements of 40 CFR 60, Appendix B, Performance Specification 1 except those for which tests are required after installation.

PDF Catalog

PDF Pages PDF Title
1 Scope
Referenced Documents
Terminology
4 Summary of Practice
TABLE 1
5 Significance and Use
TABLE 2
6 Procedure—Design Specification Verification
TABLE 3
13 Procedure—Manufacturer’s Performance Specifications
16 Quality Assurance Guidelines for Opacity monitor Manufacturers
17 Report
Keywords
A1. ADDITIONAL OR ALTERNATIVE SPECIFICATIONS FOR CERTIFYING OPACITY MONITORS FOR USE BELOW 10 % OPACITY (LOW LEVEL OPACITY MONITORS)
A1.1 General
A1.2 Procedure—Design Specification Verification
18 A1.3 Procedure—Manufacturer’s Performance Specifications
19 TABLE A1.1
20 A2. GUIDELINES FOR CALIBRATING ATTENUATORS
A2.1 General
A2.2 Calibration Spectrophotometer
A2.3 Primary Attenuator Calibration
21 A2.4 Calculation of Equivalent Transmittance Values
A2.5 Manufacturers’ Data
A2.6 Secondary Attenuator Calibration
22 X1. ERROR BUDGET FOR OPACITY MONITOR
X1.1
X1.2
X1.3
X1.4
X1.5
TABLE X1.1
23 X1.6
X2. GUIDELINES FOR ENSURING ADEQUATE PERFORMANCE OF OPACITY MONITORS
X2.1
X2.2 Recommendations for Ongoing Maintenance of Opacity Monitors
X2.3 Recommendations for Corrective Action Following a Breakdown
X2.4 Additional Recommendations
24 X3. DATA SUMMARY FORM
X3.1
FIG. X3.1
25 FIG. X3.1
26 FIG. X3.1
27 FIG. X3.1
28 FIG. X3.1
29 FIG. X3.1
30 FIG. X3.1
31 FIG. X3.1
32 FIG. X3.1
33 FIG. X3.1
34 FIG. X3.1
35 FIG. X3.1
36 FIG. X3.1
37 FIG. X3.1

Related products

ASTM-D6216
$58.50