BS ISO 492:2014
$215.11
Rolling bearings. Radial bearings. Geometrical product specifications (GPS) and tolerance values
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 78 |
This International Standard specifies dimensional and geometrical characteristics, limit deviations from nominal sizes, and tolerance values to define the interface (except chamfers) of radial rolling bearings. Nominal boundary dimensions are defined in ISO 15 , ISO 355 [2] and ISO 8443 [9] .
This International Standard does not apply to certain radial bearings of particular types (e.g. needle roller bearings) or for particular fields of application (e.g. airframe bearings and instrument precision bearings). Tolerances for such bearings are given in the relevant International Standards.
Chamfer dimension limits are given in ISO 582 .
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 9 | Section sec_1 Section sec_2 Section sec_3 Section sec_4 1 Scope 2 Normative references 3 Terms and definitions 4 Symbols |
| 10 | Table tab_1 |
| 11 | Table tab_1___1 |
| 12 | Table tab_1___2 |
| 13 | Table tab_1___3 |
| 14 | Table tab_1___4 |
| 15 | Figure fig_1 Figure fig_2 |
| 16 | Figure fig_3 Figure fig_4 |
| 17 | Figure fig_5 |
| 18 | Figure fig_6 Figure fig_7 |
| 19 | Figure fig_8 Figure fig_9 |
| 20 | Figure fig_10 |
| 21 | Figure fig_11 Figure fig_12 |
| 22 | Figure fig_13 Figure fig_14 |
| 23 | Figure fig_15 |
| 24 | Figure fig_16 |
| 25 | Table tab_a Figure fig_17 Section sec_5 Section sec_5.1 5 Limit deviations and tolerance values 5.1 General |
| 26 | Section sec_5.2 Section sec_5.2.1 Table tab_2 5.2 Radial bearings except tapered roller bearings |
| 27 | Table tab_3 |
| 28 | Section sec_5.2.2 Table tab_4 |
| 29 | Table tab_5 |
| 30 | Section sec_5.2.3 Table tab_6 |
| 31 | Table tab_7 |
| 32 | Section sec_5.2.4 Table tab_8 |
| 33 | Table tab_9 |
| 34 | Section sec_5.2.5 Table tab_10 |
| 35 | Table tab_11 |
| 36 | Section sec_5.3 Section sec_5.3.1 Table tab_12 5.3 Radial tapered roller bearings |
| 37 | Table tab_13 |
| 38 | Table tab_14 |
| 39 | Section sec_5.3.2 Table tab_15 |
| 40 | Section sec_5.3.3 Table tab_16 |
| 41 | Table tab_17 |
| 42 | Table tab_18 |
| 43 | Section sec_5.3.4 Table tab_19 |
| 44 | Table tab_20 |
| 45 | Table tab_21 |
| 46 | Section sec_5.3.5 Table tab_22 |
| 47 | Table tab_23 |
| 48 | Table tab_24 |
| 49 | Section sec_5.4 Table tab_25 5.4 Radial bearings, outer ring flanges |
| 50 | Section sec_5.5 Table tab_26 5.5 Basically tapered bores, tapers 1:12 and 1:30 |
| 51 | Table tab_27 |
| 52 | Annex sec_A Table tab_A.1 Annex A (informative) Symbols and terms as given in ISO 492:2002 in relation to descriptions given in this International Standard |
| 53 | Table tab_A.1___1 |
| 54 | Table tab_A.1___2 |
| 55 | Table tab_A.1___3 |
| 56 | Annex sec_B Figure fig_B.1 Annex B (informative) Example of drawing indications of characteristics with specification for radial bearings |
| 57 | Figure fig_B.2 |
| 58 | Annex sec_C Annex sec_C.1 Annex sec_C.2 Annex sec_C.2.1 Annex sec_C.2.2 Annex C (informative) Illustration of ISO 1132‑1 and ISO 14405‑1 terms and definitions |
| 59 | Annex sec_C.2.2.1 Annex sec_C.2.2.2 |
| 60 | Table tab_e Figure fig_C.1 |
| 61 | Table tab_f Figure fig_C.2 |
| 62 | Table tab_g Figure fig_C.3 Annex sec_C.3 Annex sec_C.3.1 |
| 63 | Annex sec_C.3.2 Annex sec_C.3.2.1 Annex sec_C.3.2.2 |
| 64 | Table tab_k Figure fig_C.4 Table tab_l Figure fig_C.5 |
| 65 | Annex sec_D Annex sec_D.1 Annex sec_D.2 Table tab_D.1 Annex D (informative) Description with illustrations for specification modifiers of linear sizes |
| 66 | Table tab_D.2 Annex sec_D.3 |
| 68 | Table tab_n Figure fig_D.1 |
| 69 | Table tab_p Figure fig_D.2 |
| 70 | Figure fig_D.3 |
| 71 | Figure fig_D.4 Annex sec_D.4 Annex sec_D.4.1 Table tab_s Figure fig_D.5 |
| 72 | Annex sec_D.5 Annex sec_D.5.1 Annex sec_D.5.2 Table tab_t Figure fig_D.6 Annex sec_D.5.3 |
| 73 | Table tab_u Figure fig_D.7 |
| 74 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Reference ref_6 Reference ref_7 Reference ref_8 Reference ref_9 Reference ref_10 Reference ref_11 Reference ref_12 Reference ref_13 Reference ref_14 Reference ref_15 Bibliography |
Related products
-
BS EN 16492:2014
Paints and varnishes. Evaluation of the surface disfigurement caused by fungi and algae on coatings…
