BS ISO 6055:2004
$102.76
Industrial trucks. Overhead guards. Specification and testing
| Published By | Publication Date | Number of Pages |
| BSI | 2004 | 18 |
This International Standard specifies the requirements and testing of overhead guards, operators’ legs and feet protection, roll-over protection system (ROPS) and falling-object protection system (FOPS) for any type of high lift, rider operated, powered industrial truck with a lift height exceeding 1 800 mm.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 3 | TitlePage – Industrial trucks�— Overhead guards�— Specification and testing |
| 5 | TableofContent – Contents Page |
| 6 | Foreword – Foreword |
| 7 | Scope – 1��� Scope NormativeReference – 2��� Normative references Clause1 – 3��� Requirements for high lift rider trucks with lift height exceeding Subclause2 – 3.1��� Introduction Subclause2 – 3.2��� General UntitledSubclause3 – 3.2.1��� The overhead guard shall extend over the operator when in the norma… |
| 8 | UntitledSubclause3 – 3.2.2��� Failure of the tilting mechanism must not, directly or indirectly, … Subclause2 – 3.3��� Dimensions UntitledSubclause3 – 3.3.1��� The guard shall be constructed in a manner that does not interfere … UntitledSubclause3 – 3.3.2��� Openings in the top of the overhead guard shall not exceed UntitledSubclause3 – 3.3.3��� For high-lift trucks on which the operator is seated, the vertical … |
| 9 | UntitledSubclause3 – 3.3.4��� For high-lift trucks on which the operator stands, the vertical cle… UntitledSubclause3 – 3.3.5��� When requested by the user, the manufacturer may reduce the normal … UntitledSubclause3 – 3.3.6��� Where the manufacturer of the overhead guard has been informed that… |
| 12 | Subclause2 – 3.4��� Testing Subclause3 – 3.4.1��� General UntitledSubclause4 – 3.4.1.1��� A dynamic and an impact drop test shall be carried out on a guard… UntitledSubclause4 – 3.4.1.2��� The same overhead guard and mounting shall be used for both tests… UntitledSubclause4 – 3.4.1.3��� In the case of specially designed overhead guards fitted to truck… UntitledSubclause4 – 3.4.1.4��� For trucks with an elevating operator position and an auxiliary l… Subclause3 – 3.4.2��� Dynamic test UntitledSubclause4 – 3.4.2.1��� The purpose of this test is to determine the resistance to perman… UntitledSubclause4 – 3.4.2.2��� The test object shall be a mass of UntitledSubclause4 – 3.4.2.3��� The test object shall be positioned to drop in free fall with the… Subclause3 – 3.4.3��� Impact drop test UntitledSubclause4 – 3.4.3.1��� The purpose of this test is to determine the permanent deformatio… UntitledSubclause4 – 3.4.3.2��� The test load shall be composed of |
| 13 | UntitledSubclause4 – 3.4.3.3��� The test load shall be centred above the overhead guard with the UntitledSubclause4 – 3.4.3.4��� The test load shall be dropped in free fall from an approximately… Subclause3 – 3.4.4��� Operators’ legs and feet protection test UntitledSubclause4 – 3.4.4.1��� The purpose of this test is to verify the strength of the structu… UntitledSubclause4 – 3.4.4.2��� The test object, as specified in Subclause2 – 3.5��� Performance requirements UntitledSubclause3 – 3.5.1��� Following the tests described in |
| 14 | UntitledSubclause3 – 3.5.2��� Following the tests described in UntitledSubclause3 – 3.5.3��� Following the test described in |
| 15 | Clause1 – 4��� Requirements for variable reach trucks with operator position not protected by the… Subclause2 – 4.1��� Introduction Subclause2 – 4.2��� General Subclause2 – 4.3��� Dimensions |
| 16 | Subclause2 – 4.4��� Testing Subclause3 – 4.4.1��� General Subclause3 – 4.4.2��� Falling objects test Subclause3 – 4.4.3��� Overturning test Subclause2 – 4.5��� Performance requirements |
| 17 | Bibliography – Bibliography |
